Qiumi Zigbee Thermostat Radiator Valve, Smart Programmable Thermostat, Temperature Heater, Alexa,Googlehome Voice Control

Product Information

We are now providing a Zigbee Device plugin mechanisms, using simple text files. These files specify mapping on a per-device type basis. The goal is to fill most of the gap with Zigbee2MQTT (provided that you write the device plugin files). The lightweight nature of plugins permits to load only the plugins required by the devices used, and does not require a software update for new devices. How does it work? ~ Valve state if open or closed. Value can be found in the published state on the valve_state property. It's not possible to read ( /get) or write ( /set) this value. If value equals OPEN valve state is ON, if CLOSED OFF. # Position (numeric) In my testing scenarios, I placed 2 TRVs near the radiator (so simulate the thermal radiation in use) alongside another temperature sensor to get neutral readings near the radiator and a few meters away to get an overall room temperature. 1st scenario

Salus - IT600 Smart Home Range Zigbee TRV Thermostatic

When a command is received, attributes are published both in their low-level and high-level formats (if known). Hello, I bought one of these last year and had the same issue as others here with the valve seeming to go open even when it was above the set temp. I gave up on it at the time but I have just updated to the latest Home Assistant and thought I would try it again, now it seems to be working fine! I bought a different, more basic, zigbee TRV from Tuya at the same time that doesn’t have any built in scheduling, this one has been running for at least a few months on the same set of batteries and works great.

Zigbee TRV

on zbreceived## do publish home/zigbee// %value% endon zigbee-herdsman-converters:tuyaThermostat: Unrecognized DP #115 with data {"status":0,"transid":180,"dp":115,"datatype":1,"fn":0,"data":{"type":"Buffer","data":[0]}} For the best consistency, I strongly suggest using sensors with a frequent polling rate. If you don’t know which sensors are these, I’m working on a comparison of ZigBee sensors– so consider following me if you want to see the data from these tests. Final thoughts I may consider getting an entire solution from one supplier, but not sure how good they are?? For example:

Zigbee for Danfoss Ally TRV? - Zigbee - Home How to setup Zigbee for Danfoss Ally TRV? - Zigbee - Home

Minimum temperature. Value can be found in the published state on the min_temperature property. It's not possible to read ( /get) this value. To write ( /set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"min_temperature": NEW_VALUE}. The minimal value is 5 and the maximum value is 15. The unit of this value is °C. # Valve state (binary) If all of the TRV’s report their current temp as 19.5 or above, no need to call for heat at this time. Some attributes are writable, but this corresponds to a change of configuration of the device. You generally can't change the status of a device writing to attributes, you need to use commands instead.MQT : tele /% t opic%/RESULT = { "ZbState" :{ "Status" : 20 , "Message" : "Disable Pairing mode" }} Example of direct binding ZbBind {"Device":"0xC2EF","ToDevice":"0x5ADF","Endpoint":1,"ToEndpoint":1,"Cluster":6} zigbee-herdsman-converters:tuyaThermostat: Unrecognized DP #119 with data {"status":0,"transid":187,"dp":119,"datatype":0,"fn":0,"data":{"type":"Buffer","data":[1,0,0]}}

Best smart radiator valves tried and tested: From Drayton

This command links the device 0xC2EF that will send all commands for cluster 6 (On/off cluster) and from endpoint 1 to the group 100. zigbee-herdsman-converters:tuyaThermostat: Unrecognized DP #119 with data {"status":0,"transid":183,"dp":119,"datatype":0,"fn":0,"data":{"type":"Buffer","data":[1,0,1]}}optional) defines a special pin used to put the MCU in bootloader and flashing mode when the hardware reset is pulled down. This is used both by EFR32 and CC2652P based devices. It allows to flash the MCU directly from Tasmota. To remove a device from the Zigbee2Tasmota list of devices and from the WebUI, use the command ZbForget or ZbForget . If the device is still connected to the network, it will pop up again later. I.e. ZbForget does not remove a device from the network; else use ZbLeave above. Advanced topic: Device Information ~ We have another new addition to our Home Assistant smart home setup with a Zigbee controlled thermostatic radiator valve (TRV) installed on the radiator in our loft workshop. That looks really nice! Thank you. Only a question: is it also possible that the valve work with a external wall thermostat? Tha you could link the setpoint of the wall thermostat and actual thermostat true Zigbee?

TRV / Radiator Valve with Home Assistant? Which Smart TRV / Radiator Valve with Home Assistant?

In this case you will have to use rules or an external home automation solution to parse those messages. The following section will focus only on rules to utilize the device inside Tasmota ecosystem. Aqara Water Leak Sensor ~ ZB-GW03 eWeLink Ethernet Zigbee Gateway (also sold as EACHEN Zigbee Smart Hub and SmartWise Zigbee Bridge Pro)The last thing to note is that the calibration offset is applied instantly to the TRV, but the local temperature usually updates every 10-15 min – and you won’t see a correct figure until the next TRV update. ECO mode (energy saving mode). Value can be found in the published state on the eco_mode property. It's not possible to read ( /get) this value. To write ( /set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"eco_mode": NEW_VALUE}. If value equals ON eco mode is ON, if OFF OFF. # Eco temperature (numeric)