Monument 2069 Compression Fitting Spanner, 24 x 32 mm

Product Information

Once the nuts are done up hand tight on the joint, an additional half to three quarter turn with a pair of spanners (one on the body of the fitting to hold it still, the other on the nut) is usually adequate to make a seal. If the joint leaks, an additional tightening tweak will normally fix it. Note that over-tightening a joint may actually make it leak. There is no significant difference. Compression fittings designed for liquid will work fine with gas but if you use optional PTFE tape, make sure it is gas grade. In addition, ensure the fittings are accessible and not hidden behind walls or under floors. Are Compression Fittings Reliable?

The process of soldering copper pipes together is referred to as ‘sweating’. Soldering offers certain advantages: it’s a straightforward process for experienced plumbers and engineers and it creates a lasting join (in theory). However, soldering is not always a practical option - in confined spaces for example. By contrast, fittings are easy to apply even without special training, do not need the application of heat, and in most cases, they can be removed and repositioned if required. How Many PSI Can a Compression Fitting Hold?The pipe needs to be cut square and cleanly, with any burrs removed. Pipes cut with a pipe cutter are much easier to use than those cut with a saw. The pipe needs to be clean and free from contaminants like paint or plaster etc. It does not need to be quite as clean and shiny as required for soldered connections. Non setting lubricants and jointing compounds like that shown above can also be applied under and over the olive. This can be more effective for fixing leaks due to pipe scratches. We are currently using Royal Mail Parcelforce and DPD as our delivery providers, all small items will be delivered by Royal Mail, these can take up to three working days to reach you. Note that this may not cure a leak that is caused by a scratch on the pipe under the olive. You may be able to wind a couple of turns under the olive - but this is less easy. The vice grip spanner is a combination of an adjustable spanner and a set of vice grip pliers (aka "mole grips"). Very handy for working at arms length in awkward spaces, and also for not marking polished chrome fittings like nuts on taps or service valves.

Compression fittings should be tight enough to create a watertight seal but not so tight that the pipe warps or the thread is damaged as this could encourage leaks and make the fittings much harder to remove later. Proceed with caution. What Should I Do if I Find a Compression Fitting Leaking? PTFE tape can also be used as a sealant - a few turns need to be wound over the olive such that they will end up sat between the mating surface between the olive and the fitting: Use of PTFE tape on both olive and threads can be of course be combined to both lubricate and seal. Most tool kits will include a set of these. While not the perfect tool, they can be very useful since they will adapt to make a good fit on any nut. If you use them with the correct orientation they also grip harder the more force you apply to them:

Sign up for special offer emails

Also means that you have twice the number of positions that the spanner can engage with the nut. This is very handy when there is very limited turning space for the spanner.

They are very skinny which makes them uncomfortable to use as well, but sometimes this slimness is an advantage where there is not much space.Slide the compression fitting olive (brass ring) over the first length of pipe, and then lay the nut over that Using a spanner, tighten the nut over the threaded head of the fitting, while holding the fitting with a pair of plumber’s grips. This pressure created by the tightening motion will press down on the olive, causing it to grip the pipe tightly. However, be careful not to exert too much pressure as this could damage the fitting or thread, making the device harder to remove or reposition An olive splitter takes a different approach by tighenting a sharp edge onto the side of the olive while supporting the pipe from the inside. They cut through one side of the olive without damaging the pipe, allowing it to expand a bit in diameter and slide off the pipe. Compression fittings are very reliable and have been proven over many decades, however sometimes things can go wrong and you end up with a joint that leaks. The common causes are: Plastic pipe can be joined with compression fittings, however it is important to use the correct brand of pipe insert to support the end of the pipe, or else the joint may start to leak over time.

Place a pipe insert into the end of the pipe to be joined. Pipe inserts, typically made from plastic or steel, reinforce pipes and keep them in a fully circular shape, making connection easier. It should be noted that this only applies to plastic pipes and not copper or steel pipes as they are much stronger Note that any sealants used on drinking water must have WRAS (Water Regulations Advisory Scheme) approval for this use. One of the difficulties with compression fittings is that while the nuts are usually a nominal size, there is not agreed standard tolerance between manufacturers. This can make selecting a single universal spanner difficult. Also not all spanner types can be used in all situations. Hence most plumbing kits will have a number of spanners, including at least one adjustable one. Copper and brass olives both work fine. Olives can't be removed from a pipe and reused. Even hand tightening a fitting with an olive inside before the pipe is inserted, is enough to make the olive unusable.These are far better suited, are long enough to get good leverage and are comfortable to use. The design of the end wraps around more of the nut giving better support and greatly reducing the risk of damaging a nut: The partially "open" end allows the spanner to slip over a pipe, and then slid onto the nut.