If you’re looking for a reliable and affordable freshwater testing kit, you should look no further. API PH Test Kit (High Range) : This is the test for PH levels from 7.4 to 8.8. It has enough solution for around 160 tests. Invert that bottle: The testing seems reliant on putting in an exact amount of both water and test solution(s). API has calibrated the solution to add in drops, but the drops need to be the correct size; namely, from an inverted bottle that is straight up and down. Also take care to not touch the dropper to the edge of the test tube as this will not result in a full drop. The water tested should initially be filled to the test tube white line, preferably following the protocol of bottom of fluid meniscus at the white line. I am very happy with the accuracy observed. I get consistent results that I can trust. As long as you follow instructions, you will be rewarded with accurate results.

API Freshwater Master Test Kit - Swell UK

Taking a few minutes each week to maintain and monitor aquarium conditions is the key to a healthy aquarium. The FRESHWATER MASTER TEST KIT tests the parameters that affect the health of freshwater fish: pH, High Range pH, Ammonia, Nitrite and Nitrate. The FRESHWATER MASTER TEST KIT is highly accurate and economical, and includes a computer calibrated, laminated color card, 4 test tubes and holding tray. The FRESHWATER MASTER TEST KIT comes with a complete, step-by-step instruction booklet, including information on how to correct unsafe water conditions. Add 5 drops of Nitrite Test Solution, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops. This testing kit is accurate, fast, and reliable, so you can depend on the results you’re getting. You can use the testing kit, even if you have no previous experience with chemicals or using testing kits. Read the test results by comparing the color of the solution to the High Range pH Color Chart. The tube should be viewed in a well-lit area against the white area of the chart. The closest match indicates the pH of the water sample. Rinse the test tube with clean water after use. Learn to raise pH levels effectively in various simple methods in a different article. High-Range pH TestEvery parameter has different instructions, so you need to be accurate while following the steps. However, all the bottles are numbered, and the steps are detailed, so you won’t struggle to get the results right. Effective Results The bottom line of testing your aquarium water with API’s liquid test comes down to reading and following exactly the instructions they provide ( API’s pdf instructions are here). It is a bit daunting in that all 5 test are unique and require slightly different instructions. They all start in the same way, and that is to fill a clean test tube (provided) with 5 ml of aquarium water (up to a white line on the side). Now add 10 drops from Nitrate Test Solution #2, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops. My only previous knowledge of aquarium water testing was with test strips. These still exist and are a good option for those that want a simple test kit. It is as easy as dipping strips of test paper directly into the aquarium for a time, removing the strip to wait for a time, then comparing the colors to a provided color chart. The advantage is the simplicity.

API Freshwater Master Test Kit (+Solutions) How To Use an API Freshwater Master Test Kit (+Solutions)

PH of tap water can change after a period of time: If you test the PH of tap water immediately after it flows from your faucet, it might read higher than you expect. The water in your pipes has a higher concentration of dissolved CO2 and this makes the PH reading high. Let a sample of tap water rest over 24 hours in an open container to off-gass this CO2, then test it. The result will be a more representative PH reading of your tap water. Read the test results by comparing the color of the solution to the Ammonia Color Chart. The tube should be viewed in a well-lit area against the white area of the chart. The closest match indicates the ppm (mg/L) of ammonia in the water sample. Rinse the test tube with clean water after use. Note that the minimum pH reading for the API Freshwater Master Test Kit is 6.0 and the maximum is 7.6. Under extreme water conditions, readings below the minimum will read 6.0, and above the maximum will read 7.6. pH Test Directions Add 8 drops from Ammonia Test Solution #1, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops. Performing partial water changes can also help reduce nitrate, especially if the level is very high. However, because many tap water supplies contain nitrate, it can be difficult to lower nitrate levels by this method.Comes with 6 bottles of liquid test reagent, 4 glass test tubes with snap-tight caps, a holding tray, and instruction booklet Testing for the presence of toxic nitrite is essential, so that if it is detected, steps can be taken to remove it. If left untreated, nitrite in the water will hinder normal fish respiration, eventually leading to fish death. Even small amounts or low levels of nitrite stress fish, suppressing their immune systems and increasing the likelihood of disease, which is why it’s important to test for nitrite using API FRESHWATER MASTER TEST KIT. You can remove nitrite from your tank by performing a partial water change. A pH of 7.0 is ideal when keeping a community aquarium containing a variety of tropical fish. That said, research is king in this department as each fish has their own recommended pH levels. In new aquariums, the nitrite level will gradually climb to 5 ppm (mg/L) or more. As the biological filter becomes established, nitrite levels will drop to 0 ppm (mg/L). In an established aquarium, the nitrite level should always remain at 0. Any level above 0 can harm fish. The presence of nitrite indicates possible over-feeding, too many fish, or inadequate biological filtration. High Nitrite Solution

API Freshwater Master Test Kit - Maidenhead Aquatics - Fishkeeper

The test kit comes with (4) mixing test tubes that you perform the tests in, (4) caps to cover the test tubes with (handy since the tests require mixing by shaking or inverting), (7) individual bottles of various fluids that are used individually or in pairs for testing, instructions, the results color chart, and a handy container that keeps it all together. The container also holds the test tubes upright for you while you perform the testing. Large pallet items like aquariums are deemed delivered successfully with no damage once the the driver has left the property. If a report of damage is submitted after the driver has left we may be unable to assist with replacements. We recommend refusing a damaged delivery, this is the fastest resolution. Add 5 drops of High Range pH Test Solution, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops. Read the test results by comparing the color of the solution to the pH Color Chart. The closest match indicates the pH of the water sample. Add 8 drops from Ammonia Test Solution #2, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops.Add 3 drops of pH Test Solution, holding the dropper bottle upside down in a completely vertical position to assure uniformity of drops. There’s a chart that explains all the steps that you need to follow while testing for different parameters.