Size does matter when it comes to PC cases or PC towers. Therefore, knowing the dimensions and specifications of both the NZXT H710 and H710i case sizes is essential. Their size determines how many important components can be installed inside and reflects how efficient the performance is.

To help you choose the right one for your needs, here is a comparison of the H710 and H710i PC cases.

This is the best NZXT H7 PC case and the one to buy for your next PC build.

If you’re familiar with the H700i, you’ll notice that the H710i doesn’t do a whole lot different here compared to that first iteration. However that’s not a bad thing, as the H710i’s internal layout is nothing short of impressive. No expense has been spared when it comes to ensuring your build experience is as seamless and pleasant as possible. The NZXT H7 Flow is capable of handling not one, but two 360mm radiators — one on the front and another up top. The rear panel has a 140mm fan and radiator mount, atop of seven horizontal PCI slots. There aren't any vertical slots with the NZXT H7 series. Finally, we've got the single tempered-glass window panel, which showcases everything instead within the case. The GPU average dT places the H710 between the H500M Mesh and the 570X on the chart. It’s not a bad score, and it’s again a couple degrees cooler than the H700i’s initial result of 52.5C dT. NZXT’s choice to ship with four fans is a valid way of making up the gap between it and cases with better airflow potential. Blender - CPU & GPU Isolated Renders In all, the H7 is slightly smaller than the H710, and it is significantly lighter. The H710 was 12.1 kg, and the new H7 is 10.26kg. That said, both cases support the same levels of CPU clearance, front fan/radiator clearance, and cable management space. The only compromise with the new H7 is that is has 13mm less GPU clearance, not that 400mm of clearance isn’t enough for practically all modern GPUs. The torture workload got the CPU to 51.9C dT average, and 46.3 dT average with the front panel removed. That’s a reasonably-sized gap and indicates that the front panel isn’t completely ruining thermals, but part of that is the fact that there are three intake fans capable of forcing air through. The dust filter is behind the front panel directly over the fans, so the perforations on either side of the front panel aren’t meant to be filters and could be completely open like the 465X. The running theme with NZXT H-series cases (perhaps excluding the H510 Elite) is thermal performance that we grudgingly admit is adequate, while at the same time airflow has been sacrificed for aesthetic reasons.

The H710i or the I version comes with the Smart Device and two pre-installed LED strips. Through CAM software, it can handle the integrated LED lighting settings and fan control.Remember, the plan is to get the H710 installed and running under ESXi 6.7 first and then upgrade to ESXi 7.0 later, once the H710 has settled in.

We’ll keep this section very brief since we’ve already reviewed most aspects of this case, but it’s worth mentioning a couple points again. First, the top and front panels are an enormous pain to remove. They’re held on with stiff clips, and the best method for defeating them is to yank the front panel violently from the bottom edge and then yank the top panel violently from the front edge. This MUST be done to remove the front filter, replace fans, or take out the radiator/fan tray at the top of the case, and it runs the risk of snapping the spindly 4.5cm clips or curving the panels and creating a gap between the front and top panels. The fan tray is still very nice, by the way--it’s held in with thumbscrews and can be flipped upside-down to move it higher away from the motherboard, and we’d like to see a similar tray at the front of the case. The NZXT H7 Elite is good for those who want to create a statement visually with the front window, whereas the normal H7 would have been good for those who don't wish to pay as much if the H7 Flow didn't cost the same. This makes it the best NZXT H7 option for those who don't want more than one tempered-glass panel (and the included RGB/fan controller hub). While NZXT’s H710 chassis has proved to be popular over its lifespan, the PC market has changed a lot since this case was introduced. For starters, CPUs and GPUs are more power-hungry than before, making airflow a greater concern for PC builders. This change to the PC market has forced NZXT to include more fan mounts on the top of their H7 series cases, adding support for top-mounted 360mm liquid cooling radiators while redesigning their front panels to enable increased system airflow. From the dimensions to the cooling system, they are nearly similar. The only difference is that the H710i is an I version that includes more features and an upgraded version over the less expensive base model H710.

Clean looks meet innovative design.

At this speed the CPU averaged 54.4C dT, not too far above baseline and better than the rest of the cases on this limited chart other than the Phanteks P400A. Despite the turbulence problems we had with the H510 Elite, NZXT’s fans proved fairly quiet in this enclosure.