As well as protection from physical damage, Armaflex Tuffcoat Outdoor Pipe Insulation is also an excellent solution for those who require waterproof external pipe insulation. Once installed and sealed, the material can withstand anything the elements can throw at it! The process of applying the lagging to your pipes is relatively straight forward, especially if you have the right tools for the job. However before you start it is worth making sure you are safe to start. Kingspan pipe insulation can be used to insulate all types of pipework including mild steel, stainless steel, carbon steel, copper, multiplex and plastic pipework. Also, pipes insulated using Kingspan phenolic pipe insulation are completely protected from thier surroundings. This increases the dew point, thereby restricting keeping condensation and pipe sweating.

Periodically you will need to join two pieces of the insulation. You should tape the join so that there is an tight seal. Some people advocate using specialist insulation tape, while this cannot hurt you can use duct tape just effectively so long as you make sure that the joints are snug and the two pieces of insulation are pushed firmly together before taping. The diameter of the pipe that this insulation will fit around. In the example below this is a 15 mm pipe. The most common sizes are 15, 22 and 28 mm When working in loft ensure that you have the correct safety gear (mask, gloves, etc) and that you are supported where you work. You don’t want to accidently put a foot through the ceiling!In terms of the tools you are going to need, here are the likely ones that you will need for fitting pipe insulation:

Kingspan Kooltherm insulation has a low thermal conductivity of 0.025 W/m*K, making it the most thermally efficient pipe lagging available. Low thermal conductivity means this phenolic foam pipe lagging does not allow heat to pass through its fabric easily. Also with an operating temperature of -50°C to +110°C, this phenolic rigid pipe insulation could be the only pipe covering you will need for your project. Kooltherm pipe insulation is suitable to insulate both heating and chilled water lines. These are often leading to outside and garden taps ( you can learn how to install an outside tap here). All pipes from your boiler or cylinder to the radiators or hot taps should be insulated to prevent unnecessary heat loss so that the maximum amount of heat is delivered to its required destination. These include: Water pipe insulation, or heating pipe insulation, can also prevent bacteria and mould from growing on pipes, which can affect how long they perform for and the areas surrounding them. If pipes begin to grow mould in a timber frame building they could spread this into the wood or even into surrounding insulation.

Exposed external pipework in likely to freeze in winter when the air temperature drops below freezing and this can cause the pipes to burst. Pipes in Lofts Another great feature of this premium performance pipe insulation is its outstanding fire resistance. Its dense cross-linked structure creates a carbonaceous layer that limits the spread of flame and heat in case of a fire. It is also lightweight, making it easy to install. And because it has a very low thermal conductivity, it is also ideal for use in confined spaces. How to choose Kingspan kooltherm phenolic foam Pipe Insulation Online? You might see different types of pipe insulation, but typically the most cost effective option that you will be able to buy is the polyethylene foam type. You should be able to get this at any DIY shed. Therefore, this high performance pipe insulation, not only prevents moisture from the surroundings from entering the pipes or the application but also stops mould growth and prevents condensation. This in turn protects pipes from corrosion. Kingspan Pipe Insulation is Environmentally-Friendly:

Behind the pipe push the insulation so that each side of the split meets around the pipe. Then to ensure that it cannot become dislodged you should tape in in place. Sometimes people prefer to use cable ties, but it doesn’t really matter so long as the insulation is kept snugly fit around the pipe: To choose the right Kingspan kooltherm phenolic foam pipe insulation for your application you will first need to know the type of pipe you are insulating and also its size or outer diameter. Copper pipes are thinner, so if the pipe size is 15mm, a 15mm pipe section will work for your application. We have a video on our Youtube Channel you can watch called Everything You Need To Know About Phenolic Pipe Insulation We have lots of projects all about insulation and draught proofing should you need more advice here. Kooltherm pipe insulation can be used to insulate all types of pipework. The insulation is suitable for mild steel, carbon and stainless steel, copper pipes, multiplex and plastic pipework.

Additionally, this pipe insulation is supplied with a foil vapour barrier that not only stops the entry of water into the application but also reflects radiant heat thereby adding to its thermal performance. Kingspanpipe insulationsections have been developed to give optimum performance in terms of insulation efficiency, compressive strength, fire resistance, and most importantly, cost. It gives excellent value for money. Due to its closed-cell structure, phenolic foam pipe lagging from Kingspan Insulation restricts moisture ingress. What's more, they also have foil facings on the outside, that act as an additional moisture barrier to the application. Kingspan Kooltherm is made with phenolic foam. But, what is phenolic insulation or phenolic foam insulation? Where the pipes are fixed to the wall with clips this will get in the way of fitting the insulation. There are two options to deal with this:

Foil pipe insulation with a closed-cell structure offers high resistance to moisture ingress and permeation whichprotects pipes from moisture issues such as corrosion and adverse reactions. As we mentioned you will typically use the foam type insulation which have already be cut with a slit so that it can easily be fit over a pipe: We have also written extensive articles on the subject which you can find here - Pipe Insulation Articles For straight runs:Measure the length of the pipe you have to insulate. Wipe the pipe surface clean and free of any oil or debris. Cut the Kingspan Kooltherm section using a sharp utility knife and slide it over the pipe. Use foil tape or adhesive to seal the ends of the insulation together. Kooltherm technical pipe insulation is also rated Eurofins Indoor Air Comfort Gold, which means this foam pipe lagging does not harm the surroundings or its air quality in any way. Best pipe lagging for confined spaces:It's only really bested by Aerogel pipe insulation, which is not something that is widely available due to its cost and difficulty to install. Therefore it could be said that Kingspan pipe insulation isthe best pipe lagging if judged by its ability to thermally insulate pipework alone. It is easy to install and works well on all kinds of pipework across project types. Make sure that you insulate the whole length of the exposed pipe work, including any couplings, joins and event taps.