Thanks to the low modulus of elasticity of Mapei Mapesil LM Silicone, it is suitable for sealing internal and external fillet and expansion joints, including those subject to high levels of movement when in service, between: Pre-fabricated panels, window/door fittings and wall surrounds, pipe-work and vertical walls, similar and/or different types of coating materials. It is also suitable for sealing joints in doors with limited pedestrian traffic. Where Mapei Mapesil AC is to be applied in areas of continuous immersion, i.e. inside a swimming pool tank, the joints must be primed using Mapei Primer FD.

Mapei Ultracolor Plus is available in 2kg and 5kg bags, in the following colours: Please note, only some colours are available in 2kg bags. Mapei Mapesil AC Silicone is a one-component, acetic crosslinking, solvent-free silicone sealant, available coloured or transparent. It is a thixotropic paste which is easily trowellable both horizontally and vertically. Mapei Mapesil AC Silicone crosslinks following exposure to atmospheric humidity at ambient temperatures, and forms an elastic product with following properties: Preparing the mix: While stirring, pour the Mapei Ultracolor Plus Grout powder into a clean, rust-free container containing 21-23% by weight of clean water. Mix the grout with a low-speed mixer to avoid air entrainment, until a smooth paste is obtained. Let the mix stand for 2-3 minutes, and stir again briefly before use. Use the mix within 20-25 minutes of its preparation. Mapei Ultracolor Plus is suitable for grouting walls and floors in areas that are subject to intense traffic, such as shopping centres, airports, restaurants and other public spaces. It is also suitable for residential use in all areas, such as facades, balconies, terraces and swimming pools. When Mapei Mapesil LM is exposed to the air, the surrounding humidity sets off the cure reaction and the sealant becomes flexible. The surrounding temperature only has a small impact on the cure rate of Mapei Mapesil LM, while the level of humidity in the surrounding air has the most influence. We highly recommend that the product is never applied if the temperature is below 0°C.The resistance of Mapei Mapesil AC to chemical agents is generally excellent; however, due to the numerous products and working conditions to which Mapei Mapesil AC can be applied, it is always advisable to do a sample test in cases of doubt. Mapei Ultracolor Plus does not contain Portland cement and must not be mixed with gypsum or other hydraulic binders; never add water to the mix once it has started to set.

To control the depth of the joint and to prevent Mapei Mapesil AC Silicone from adhering to the base, the bottom of the joint should be filled with a sized Mapefoam, a polyethylene cord Application of Mapei Primer FD: Where the use of Primer FD is necessary, it must be applied with a small brush onto the appropriate areas of the joints and left to dry for several minutes to allow the solvent to evaporate. Then apply Mapei Mapesil AC Silicone. Mapei Mapesil LM does not emit unpleasant odours, and comes in the form of a thixotropic paste. It is easy to apply on vertical and horizontal surfaces and cures at room temperature through the humidity present in the air to form a flexible sealant. Seals made using Mapei Mapesil LM are extremely stable over time, even when exposed to inclement weather, industrial environments, temperature variations or water. The product remains flexible over a temperature range of between -40°C and +150°C. Mapei Mapesil LM Silicone Sealant is a neutral, mould-resistant silicone sealant with very low emission level of volatile organic compounds (VOC), for use with natural stone and marble.

Solseal Delivery Schedule

Do not use Mapei Mapesil LM for sealing doors subject to intense traffic – (use Mapeflex PU45, Mapeflex PU20 or Mapeflex PU21). Finishing: When the mix loses its plasticity and becomes opaque, which usually takes place after 15-30 minutes, clean off the excess Ultracolor Plus with a hard, damp sponge (e.g. a MAPEI sponge), working in a diagonal direction to the joints. Rinse the sponge frequently, using two different containers of water: one to remove the excess mix from the sponge, and the other, containing clean water, to rinse the sponge. This operation may also be carried out with a machine with a sponge belt or rotating disc. When the mix is partially set, after 50-60 minutes, a damp Scotch-Brite® sponge or an abrasive felt disc may be passed over the joints to even out the surface. Sealing joints in wall and floor coverings of ceramic and cement, provided they are not subject to heavy abrasion. Under certain conditions Mapei Mapesil LM Silicone may have a water-repellent effect along the edges of joints. This effect is only noticeable when surfaces are wet and is invisible when the same surfaces are dry. This phenomenon, however, has no effect on the product’s performance characteristics. Do not use Mapei Primer FD when sealing stone or marble.